NAD M 22.2 Stereo Power Amplifier
Hybrid Digital Amplification
The M22 is using the latest nCore™ amplifier technology licensed from Hypex to provide a nearly ideal amplifier with distortion below measurement, ultra-high damping factor, and unconditional stability with any speaker. Tight, detailed sound with amazing control and transparency gets the best performance available. With nCore, Hypex has refined their UcD concept to new levels of perfection by improving the modulator for more accurate feedback subtraction and PWM generation. The all-discrete driver and output stage have also been improved for lower open-loop THD as well as lower idling losses, normally conflicting requirements with conventional IC driver circuitry. An added control loop incorporating an integrator with adaptive clipping enables 20dB more feedback to be used across the audio band because of its extremely low-phase shift resulting in a dramatic reduction in distortion across the audio band. This is added to UcD’s already amazing characteristics of load invariance and high current capability, common characteristics of great-sounding amplifiers.
Effortless Power
Employing the latest generation of digital PowerDrive™, the M22 offers a minimum of 300W per channel with amazing reserves of dynamic power at lower impedances. The M22 is capable of >400W dynamic power per channel even in 8 ohms, >700W in 4 Ohms, and 1,000W in 2 ohms. Need more power? Select Bridge Mode and the M22 offers 950W at 8 Ohms in Mono. It can effortlessly power any loudspeaker to live performance levels with amazing efficiency and low power consumption. Control for PowerDrive is derived by sensing the average output power, applying a time constant, and then cleanly hard clipping the signal thus limiting it to the rated continuous clipping power over a sustained loading. By controlling the power envelope maximum clean power is obtained for every operating condition.
Perfecting Performance
The output stage is only one of several circuits in the amplifier, and each must complement the other to obtain optimal performance. The amp is DC coupled throughout, from input to output, there is no capacitor in the forward signal path. Yet, it has a beneficial 12dB/octave roll-off below 2Hz. It does this using a unique circuit topology that is functionally a forward servo. It is however not a servo in the traditional sense as it does not measure DC at the output and send back a correction signal. Instead part of the input signal is fed to a side chain with a second order low-pass filter. The output of this is subtracted from the forward signal input to the second stage thus rejecting DC.
Clean and Dynamic
The performance of the entire signal path is critically dependent on the power supply; in this case a well regulated, but not too tight, custom switch mode design. This allows maximum dynamic power, very high current yet with very low distortion. Secondary supplies are individually regulated and decoupled at each opamp for lowest possible noise and maximum dynamic range.
Audio Specifications
Hybrid Digital Amplification
The M22 is using the latest nCore™ amplifier technology licensed from Hypex to provide a nearly ideal amplifier with distortion below measurement, ultra-high damping factor, and unconditional stability with any speaker. Tight, detailed sound with amazing control and transparency gets the best performance available. With nCore, Hypex has refined their UcD concept to new levels of perfection by improving the modulator for more accurate feedback subtraction and PWM generation. The all-discrete driver and output stage have also been improved for lower open-loop THD as well as lower idling losses, normally conflicting requirements with conventional IC driver circuitry. An added control loop incorporating an integrator with adaptive clipping enables 20dB more feedback to be used across the audio band because of its extremely low-phase shift resulting in a dramatic reduction in distortion across the audio band. This is added to UcD’s already amazing characteristics of load invariance and high current capability, common characteristics of great-sounding amplifiers.
Effortless Power
Employing the latest generation of digital PowerDrive™, the M22 offers a minimum of 300W per channel with amazing reserves of dynamic power at lower impedances. The M22 is capable of >400W dynamic power per channel even in 8 ohms, >700W in 4 Ohms, and 1,000W in 2 ohms. Need more power? Select Bridge Mode and the M22 offers 950W at 8 Ohms in Mono. It can effortlessly power any loudspeaker to live performance levels with amazing efficiency and low power consumption. Control for PowerDrive is derived by sensing the average output power, applying a time constant, and then cleanly hard clipping the signal thus limiting it to the rated continuous clipping power over a sustained loading. By controlling the power envelope maximum clean power is obtained for every operating condition.
Perfecting Performance
The output stage is only one of several circuits in the amplifier, and each must complement the other to obtain optimal performance. The amp is DC coupled throughout, from input to output, there is no capacitor in the forward signal path. Yet, it has a beneficial 12dB/octave roll-off below 2Hz. It does this using a unique circuit topology that is functionally a forward servo. It is however not a servo in the traditional sense as it does not measure DC at the output and send back a correction signal. Instead part of the input signal is fed to a side chain with a second order low-pass filter. The output of this is subtracted from the forward signal input to the second stage thus rejecting DC.
Clean and Dynamic
The performance of the entire signal path is critically dependent on the power supply; in this case a well regulated, but not too tight, custom switch mode design. This allows maximum dynamic power, very high current yet with very low distortion. Secondary supplies are individually regulated and decoupled at each opamp for lowest possible noise and maximum dynamic range.
Audio Specifications
- Continuous output power into 8 ohms and 4 ohms (Stereo mode)
- 300 W (20 Hz-20 kHz at 0.1% THD, both channels driven)
- Continuous output power into 8 ohms (Bridge mode) THD+N (20 Hz – 20 kHz, CCIF IMD, SMPTE IMD, DIM 100)
- 900 W (20 Hz – 20 kHz at 0.1% THD)
- <0.005 % (250 mW to 290W, 8 ohms and 4 ohms)
- Note: Measured with Audio Precision AUX-0025 or Prism dS-LPF passive low pass filter
- Signal-to-Noise Ratio
- >100 dB (A-weighted, ref. 1 W in 8 ohms
- >120 dB (A-weighted, ref. 300W in 8 ohms)
- Clipping power (Stereo mode, at 1 kHz 8 ohms 0.1 % THD)
- >300 W
- Clipping power (Bridge mode, at 1 kHz 8 ohms 0.1 % THD)
- >950 W
- IHF dynamic power (Stereo mode, at 1 kHz 1 % THD)
- 8 ohms: 400 W
- 4 ohms: 700 W
- 2 ohms: 1000 W
- Damping factor
- >800 (ref. 8 ohms)
- Frequency response
- ±0.1 dB (20 Hz – 20 kHz)
- Input sensitivity (for 300W in 8 ohms)
- 1.73 V
- Gain level
- Low: 19 dB
- Medium: 24 dB
- High: 29 dB
- Minimum input level for Auto Trigger
- 5 mV at 1 kHz
- Standby power
- <0.5 W
- Gross dimensions (W x H x D): 435 x 103 x 379 mm / 17 1/8 x 4 1/16 x 14 15/16 inches
- Net Weight: 8.9 kg (19.6 lbs)
- Shipping Weight: 15 kg (33.1 lbs)
PDF-Product information
You have to be logged in and must have bought this product to write a review.
- No review available for this item.
You receive a 2 year warranty from the date of purchase for all of our high quality hifi-products.
If you observe any problem while using the product, you have the possibility to contact our friendly service team.
You can also easily manage your guarantee concern – without being obliged to – under the section My Account.
Warranty extention on NAD products
You have the possibility to extend the warranty on NAD products for free.
In total, the manufacturer offers a warranty of 5 years from the date of purchase.
You will need to send an eMail with the following data to this address: kontakt@dali-speakers.de
• First Name:
• Last Name:
• Street:
• ZIP Code:
• City:
• E-Mail:
• Brand:
• Modell:
• Color:
• Serialnumber:
• Date of purchase:
• Invoice as proof of sale (as an attachment)
If you observe any problem while using the product, you have the possibility to contact our friendly service team.
You can also easily manage your guarantee concern – without being obliged to – under the section My Account.
Warranty extention on NAD products
You have the possibility to extend the warranty on NAD products for free.
In total, the manufacturer offers a warranty of 5 years from the date of purchase.
You will need to send an eMail with the following data to this address: kontakt@dali-speakers.de
• First Name:
• Last Name:
• Street:
• ZIP Code:
• City:
• E-Mail:
• Brand:
• Modell:
• Color:
• Serialnumber:
• Date of purchase:
• Invoice as proof of sale (as an attachment)
Other Products
-
AVM Evolution PA 3.2 Preamplifier black
3.092,60 € -
-5 %
Cayin CS-100A tube integrated amplifier KT 88 aluminium front silver
RRP4.298,00 €
4.083,10 € -
AVM Evolution PA 3.2 Preamplifier
3.092,60 € -
Marantz SACD 30n SA-CD Player with DAC
RRP2.999,00 €
from 2.989,00 € -
-3,2 %
Marantz SR 8015 AV-Receiver 11.2 Chanel Full 8K Ultra HD with Heos Build-In, AirPlay2, Alexa
RRP3.099,00 €
2.999,00 € -
Marantz Model 30 Amplifier with Phono silver/gold
RRP2.999,00 €
2.995,00 € -
-5 %
Cayin CS-88 tube integrated amplifier with phono
RRP3.399,00 €
3.229,05 € -
-17 %
Denon AVC-X8500H 13.2 Chanel 4K-AV-Receiver with Amazon Alexa silver
RRP3.999,00 €
3.299,00 €