Proburn Cable-Cooker
Avoid the suffering and time consuming burn-in process of your new cables
It's a well-known fact that high-quality audio and video cables improve over time when used in a hifi or home cinema system. A hard, closed in sound with a distinct lack of bass are the qualities most noted when a cable is new; a cable that has been ‘burned-in’ will sound more open, extended and three dimensional, with a more natural, less sterile overall performance.
Unfortunately, most high quality specialist cables only get close to realising their full potential after months of use. Playing wide bandwidth music gradually improves the performance of speaker and interconnect cables, yet technically they will never reach optimum performance with music signals alone.
The problem is quite simple. Real music has very little high frequency energy, and thus will have a limited ability to improve a cable. Research shows that musical instruments may produce energy above 20 kHz, but there is little sound energy above 40 kHz. Also, most microphones do not pick up sound at much over 20 kHz.
The challenge is two-fold: burn in time and burn in effectiveness. How can a cable be fully conditioned, and the time required to undertake this conditioning decreased from several months to just one day? It is critical to not only concentrate on the conductor, but also the dielectric. Ideally, cable burn-in needs to force electrons into all areas of the cable; this is something that simply playing music through an audio system can never achieve.
The Proburn cable burn-in accelerator not only dramatically reduces the burn-in time of all cables, but also fully prepares them. Proburn does more than simply synthesise music; using specially developed technology, the unit generates a sequence of unique ultra low frequencies to penetrate the core of the conductor, and ultra high frequencies that penetrate both the conductor and the dielectric.
Using conventional methods, it’s extremely difficult to condition the dielectric of a cable, yet this is exactly where effort should be focused. Using carefully controlled energy levels and frequencies, electrons are forced and attempt to enter the dielectric. Imagine a high frequency, high energy force zipping along the conductor surface in a corkscrew fashion between the conductor and into the dielectric; the malingering electrons and negative charges are then forced to join the procession.
Through this technique of ultra low and ultra high frequencies in a musical synthesis, the cable is fully prepared and burned in within 24 to 48 hours. This guarantees total penetration of the core of the cable, and also that the interface between the outer conductor surface and dielectric is fully and properly conditioned. This patent pending technique fully prepares cables for audio or video. To put this into context, Proburn produces 10,000 times the upper frequency limit of a typical CD player, which not only dramatically reduces the burn-in time for new cables but also fully prepares and conditions your existing cables. Proburn will also keep your cables performing to their full potential; the only thing you'll have to do is to condition them for 24 hours every six to eight weeks.
Features
Avoid the suffering and time consuming burn-in process of your new cables
It's a well-known fact that high-quality audio and video cables improve over time when used in a hifi or home cinema system. A hard, closed in sound with a distinct lack of bass are the qualities most noted when a cable is new; a cable that has been ‘burned-in’ will sound more open, extended and three dimensional, with a more natural, less sterile overall performance.
Unfortunately, most high quality specialist cables only get close to realising their full potential after months of use. Playing wide bandwidth music gradually improves the performance of speaker and interconnect cables, yet technically they will never reach optimum performance with music signals alone.
The problem is quite simple. Real music has very little high frequency energy, and thus will have a limited ability to improve a cable. Research shows that musical instruments may produce energy above 20 kHz, but there is little sound energy above 40 kHz. Also, most microphones do not pick up sound at much over 20 kHz.
The challenge is two-fold: burn in time and burn in effectiveness. How can a cable be fully conditioned, and the time required to undertake this conditioning decreased from several months to just one day? It is critical to not only concentrate on the conductor, but also the dielectric. Ideally, cable burn-in needs to force electrons into all areas of the cable; this is something that simply playing music through an audio system can never achieve.
The Proburn cable burn-in accelerator not only dramatically reduces the burn-in time of all cables, but also fully prepares them. Proburn does more than simply synthesise music; using specially developed technology, the unit generates a sequence of unique ultra low frequencies to penetrate the core of the conductor, and ultra high frequencies that penetrate both the conductor and the dielectric.
Using conventional methods, it’s extremely difficult to condition the dielectric of a cable, yet this is exactly where effort should be focused. Using carefully controlled energy levels and frequencies, electrons are forced and attempt to enter the dielectric. Imagine a high frequency, high energy force zipping along the conductor surface in a corkscrew fashion between the conductor and into the dielectric; the malingering electrons and negative charges are then forced to join the procession.
Through this technique of ultra low and ultra high frequencies in a musical synthesis, the cable is fully prepared and burned in within 24 to 48 hours. This guarantees total penetration of the core of the cable, and also that the interface between the outer conductor surface and dielectric is fully and properly conditioned. This patent pending technique fully prepares cables for audio or video. To put this into context, Proburn produces 10,000 times the upper frequency limit of a typical CD player, which not only dramatically reduces the burn-in time for new cables but also fully prepares and conditions your existing cables. Proburn will also keep your cables performing to their full potential; the only thing you'll have to do is to condition them for 24 hours every six to eight weeks.
Features
- Generates specific ultra low and ultra high frequencies to optimise cable performance
- Produces 10,000 times the upper frequency limit of a typical CD player
- Dramatically reduces the burn-in time required by new cables to within 48 hours
- More effective at optimising cable performance than music signals alone
- Keeps cables performing at their best - condition them for a period of 24 hours, every six to eight weeks
- Outlets 4 pairs speakers terminals, 2 pairs of RCA terminals and 1 pair of XLR terminals
- Voltage 90-264 Vac
- Weight 1 kg
- Dimensions 170x70x105 mm
You have to be logged in and must have bought this product to write a review.
- No review available for this item.
You receive a 2 year warranty from the date of purchase for all of our high quality hifi-products.
If you observe any problem while using the product, you have the possibility to contact our friendly service team.
You can also easily manage your guarantee concern – without being obliged to – under the section My Account.
If you observe any problem while using the product, you have the possibility to contact our friendly service team.
You can also easily manage your guarantee concern – without being obliged to – under the section My Account.
Other Products
-
Pro-ject Power Box RS2 Sources Universal linear power supply for 4 RS/RS2 devices black
999,00 € -
Pro-Ject Power Box RS2 Phono linear-power-supply for turntable and preamp black
899,00 € -
MICHELL Never Connect H.R. Power Adapter
989,00 € -
Pro-Ject Power Box RS2 Phono linear-power-supply for turntable and preamp silver
899,00 € -
Pro-ject Power Box RS2 Sources Universal linear power supply for 4 RS/RS2 devices Silver
999,00 € -
Pro-Ject Power Box RS2 Phono linear-power-supply for turntable and preamp
899,00 € -
Pro-ject Power Box RS2 Sources Universal linear power supply for 4 RS/RS2 devices
999,00 € -
NAD HTR-10 Learning Remote Control
129,00 €