WBT-0765
Pole Terminal, isolated and gold plated
Note: Minimum purchase = 4 pieces!
gold-plated with Makrolon full insulation, CE and IEC compliant
Outer connection
>> 4 mm banana plug
A 4 mm banana plug can be connected in the front part of the clamping nut.
>> Spades and crimped cable ends (up to 6 mm²/ 9 AWG)
You can use the patented WBT clamping nut system to make high-pressure spade and crimped cable end connections. The cross-milled surface on the bottom of the pressure piece creates a permanently secure connection with extremely low transition resistance. It also prevents the splitting of cable strands if exposed cable ends are used.
Inner connection
Cables with a conductor cross section of up to 10 mm² (7 AWG) can be used on the inside. The connections can be soldered or crimped.
For soldered connections, WBT recommends the surface-friendly silver solder WBT-0800.
For crimp connections, an additional T.6 Torx screw is required.
Mounting
Mounting insulators are supplied and ensure not only insulated but also twist-proof mounting and polarity identification. Counter nuts, double step washers with lug and puzzle plates are also supplied. The puzzle plates can be clipped into one another. This ensures precise terminal spacing of 19 or 30 mm, but above all absolute torsion protection.
The nuts on appliances with high intrinsic mechanical vibration levels like loudspeakers should be additionally secured – using the WBT serrated lock washer WBT-9150, for example. In case a fixed distance of 19 mm is required, one may use the spacer WBT-9404 and install the WBT-0765 as a double terminal. Thanks to the locking slots in the spacer the inlet opening for the connection cable can be rotated in steps of 45°.
(WBT-9404 is supplied with each end consumer package, but in general needs to be ordered separately.)
Hint for OEMs
Due to the current safety regulations, the 4 mm banana holes of WBT pole terminals should be closed using the safety stick WBT-0799.
Pole Terminal, isolated and gold plated
Note: Minimum purchase = 4 pieces!
gold-plated with Makrolon full insulation, CE and IEC compliant
- Extremely high contact pressure for spades thanks to fine thread and cross-milled surface
- Pat. two-piece clamping nut for maximum strength of connection
- Solder or crimp connection
- CE and IEC compliant thanks to full Makrolon insulation
- 24 carat multi layer gold plating
- Max. constant current 70 A
- Twist-proof mounting
- Puzzle plate system
Outer connection
>> 4 mm banana plug
A 4 mm banana plug can be connected in the front part of the clamping nut.
>> Spades and crimped cable ends (up to 6 mm²/ 9 AWG)
You can use the patented WBT clamping nut system to make high-pressure spade and crimped cable end connections. The cross-milled surface on the bottom of the pressure piece creates a permanently secure connection with extremely low transition resistance. It also prevents the splitting of cable strands if exposed cable ends are used.
Inner connection
Cables with a conductor cross section of up to 10 mm² (7 AWG) can be used on the inside. The connections can be soldered or crimped.
For soldered connections, WBT recommends the surface-friendly silver solder WBT-0800.
For crimp connections, an additional T.6 Torx screw is required.
Mounting
Mounting insulators are supplied and ensure not only insulated but also twist-proof mounting and polarity identification. Counter nuts, double step washers with lug and puzzle plates are also supplied. The puzzle plates can be clipped into one another. This ensures precise terminal spacing of 19 or 30 mm, but above all absolute torsion protection.
The nuts on appliances with high intrinsic mechanical vibration levels like loudspeakers should be additionally secured – using the WBT serrated lock washer WBT-9150, for example. In case a fixed distance of 19 mm is required, one may use the spacer WBT-9404 and install the WBT-0765 as a double terminal. Thanks to the locking slots in the spacer the inlet opening for the connection cable can be rotated in steps of 45°.
(WBT-9404 is supplied with each end consumer package, but in general needs to be ordered separately.)
Hint for OEMs
Due to the current safety regulations, the 4 mm banana holes of WBT pole terminals should be closed using the safety stick WBT-0799.
- Conductor cross section (max.): outside: 6 mm² (9 AWG)
- inside: 10 mm² (7 AWG)
- Connection technology: outside: 4 mm banana plug, spades (6 - 8 mm spade), crimping
- inside: crimping (T.6 Torx screw required) or soldering
- Wall thickness: 0.1 - 10 mm
- Identification: red, white or black
- Installation: with the spacer WBT-9404 also as a double terminal
Technical drawing
PDF-Product information
You have to be logged in and must have bought this product to write a review.
- No review available for this item.
You receive a 2 year warranty from the date of purchase for all of our high quality hifi-products.
If you observe any problem while using the product, you have the possibility to contact our friendly service team.
You can also easily manage your guarantee concern – without being obliged to – under the section My Account.
If you observe any problem while using the product, you have the possibility to contact our friendly service team.
You can also easily manage your guarantee concern – without being obliged to – under the section My Account.
Other Products
-
-15 %
Monacor AT 52 ST - Stereo-Levelcontrol
RRP38,37 €
32,61 € -
-10 %
Monacor SPH 68 X/AD Fullrange
RRP45,64 €
41,08 € -
-12 %
Monacor DT 100 Soft Dome
RRP36,54 €
31,90 € -
-15 %
Mundorf BS stack-core baked varnish with feron 6,8 mH
RRP69,90 €
59,42 € -
-17 %
Mundorf Baked Varnish Coil 1.0 CU 6,8 mH
RRP38,90 €
32,08 € -
-6 %
Dynaudio Esotec Grilles (Pair) MW 152
RRP32,00 €
30,08 € 2 piece | 15,04 € /piece -
-6 %
Scan Speak D 2604/830000 Textile Tweeter
RRP48,00 €
45,12 € -
Spare Diaphragm Beyma CP 16
34,00 €