Dynaudio Home Cinema 5.0 Set Emit 30, Emit 25C and Emit 10


manufacturer information
-10 %

RRP 2.906,00 €

incl. 19% VAT (Deutschland) plus shipping
Please choose variant:
-10 %
Dynaudio Home Cinema 5.0 Set Emit 30, Emit 25C and Emit 10

The set consists of:

2 X Dynaudio Emit 30
2 X Dynaudio Emit 10
1 X Dynaudio Emit 25C


Dynaudio Emit 30 Floorstanding-Speakers

Emit 30 is perfect for larger stereo systems or compact multi-channel home cinema set-ups in medium to large rooms.

If you’re looking for a little more power from your system, you’ve found it. Emit 30 is a compact two-and-a-half-way speaker designed to impress whether it’s used as a stand-alone stereo pair or as part of a 5.1-channel (or more) home cinema.

Like its little brother, Emit 10, it uses 14cm MSP woofers similar to those used in the Evoke series – this time doubled-up in each speaker for more low-frequency muscle, plus midrange clarity and punch. MSP stands for Magnesium Silicate Polymer. It’s a material we developed in-house for our woofer cones, and have used for decades – including on our most-lauded high-end models. MSP provides precisely the right combination of lightness, stiffness and damping (one we’ve tuned and honed over the years) to deliver control and outright power exactly where it’s needed.

Premium woofer technology

The cones are moulded in one piece; we don’t use a separate glued dust-cap. The little balance ribs around the edge of the centre are bonded directly to the voice-coil behind it, making the whole motor assembly one solid piece. Using fewer moving parts gives our engineers fine control over how the speaker moves – which, in turn, means fine control over how it performs. You’ll hear it as strong, tight bass and startlingly clear vocals, guitars and more. Even at eyebrow-raising volume.

Each woofer is powered by a dual-stacked strontium carbonite Ferrite+ ceramic magnet system. Using two magnets means we can more effectively direct where the magnetic energy goes – it’s a lesson we learned developing the award-winning Special Forty anniversary series, and it’s thrilling to be able to use it in our entry-level family.

The target for all that flux is the voice-coil. We use aluminium windings in Emit 30. Aluminium is light (which minimises inertia on the cone’s back-and-forth movement), and because it’s lighter than copper wire, it means we can pack more windings on to the two-layer glass-fibre former. More windings equals more power, and greater control over fine movement. There’s a twist, though (please pardon the pun): we’ve coated the aluminium wire in a very thin copper coating to further increase the control the amplifier has on the voice-coil. More force with only a fractional weight gain: win-win.

High-performance Cerotar tweeter

While the twin 14cm mid/bass units deal with the… well, midrange and bass… the upper frequencies are handled by the tweeter. Emit might be an ‘entry-level’ speaker, but we certainly haven’t used any old unit off the shelf; witness the incredible Cerotar tweeter (the same as we use in Evoke). It’s based on the Esotar Forty anniversary tweeter and the Esotar Pro found in our Core studio reference speakers, and must be heard to be believed.

The 28mm coated soft-dome diaphragm is backed up by the clever Hexis inner dome. The playing surface has been specifically engineered to produce ultra-clear, ultra-detailed high-frequencies without breakup (even at high volumes), while the Hexis smooths the airflow behind it to reduces unwanted resonances. An aluminium voice-coil and airflow magnet system provide the power. Cerotar is designed for high performance without listener fatigue – perfect if you’re given to long listening sessions (and you’re music lovers, so we bet you are).

The bass-port on the back panel has dual flares (one inside; one outside), and has been tuned to minimise unwanted ‘chuffing’. It’s supplied with foam inserts that can be used to optimise performance for the speaker’s position relative to the wall.

Danish-designed cabinetry

Emit 30’s cabinets are made from 18mm MDF to provide a solid, stable platform for the drivers to do their work. They’re internally damped with polyester fibre, measured down to the gram for exactly the right amount of resonance suppression.

On the outside, you can choose from three custom laminate finishes: Black, White or Walnut. They’ve been chosen to complement any room, in any configuration (so if you’re mixing and matching Emit speakers in a home cinema system, you can make them stand out or blend in as you want).

Emit 30: powerful floorstander performance in a compact package. If you want to take your listening to the next level, they’ll really make your collection sing.

Features

Hi-fi starts with Emit - Designed and engineered in Denmark


The entire Emit family has been put through its paces in our world-class Jupiter measuring facility at Dynaudio Labs. We treat it exactly the same as we do every other speaker in our range: no stone left unturned.

Cerotar tweeter

Emit uses the highly regarded Cerotar tweeter from our Evoke series. It's a high-quality high-frequency driver inspired by our top-end Confidence and Heritage Special speakers, and includes the innovative resonance-defeating Hexis inner dome.

Clean and simple

Each speaker in the Emit range is designed to fit with modern lifestyles and interiors. Clean lines, simple finishes and minimalist Scandinavian looks – whether you're listening in stereo or have a full multi-channel system.

Specifications
  • Sensitivity: 87dB (2.83V/1m)
  • IEC power handling: 180 watt
  • Impedance: 4 Ω
  • Frequency response (± 3 dB): 44Hz - 25kHz (-6 dB 39 Hz - 35 Khz)
  • Box principle: 2 X Bass reflex rear double flared port
  • Crossover: 2.5-way
  • Crossover frequency: 1000/3550Hz
  • Crossover topology: 1ST order tweeter / 2nd order woofer
  • Midrange / Woofer: 14 cm MSP
  • Woofer: 14 cm MSP
  • Tweeter: Cerotar soft dome with Hexis
  • Weight: 15.53 kg / 34.2 lb
  • Dimensions (W x H x D): 170 X 900 X 271,5 mm /  6.7 X 35.4 X 10.7 in
  • Dimensions with feet/grille (W x H x D): 267,5 X 946,5 X 335,4 mm /  10.5 X 37.3 X 13.2 in
Dynaudio Emit 10

Specifications
  • Sensitivity: 85dB (2.83V/1m)
  • IEC power handling: 150 watt
  • Impedance: 6 Ω
  • Frequency response (± 3 dB): 64Hz - 25kHz (-6 dB 52 Hz - 35 Khz)
  • Box principle: Bass reflex rear double flared port
  • Crossover: 2-way
  • Crossover frequency: 3700 Hz
  • Crossover topology: 1ST order tweeter / 2nd order woofer
  • Midrange / Woofer: 14cm MSP cone
  • Tweeter: Cerotar soft dome with Hexis
  • Weight: 6.43kg / 14.2 lb
  • Dimensions (W x H x D): 170 X 290 X 271,5 mm /  6.7 X 11.4 X 10.7 in
  • Dimensions with feet/grille (W x H x D): 170 X 290 X 284,5 mm /  6.7 X 11.4 X 11.2 in
Dynaudio Emit 25C Center-Speaker

It’s been said that the soundtrack is up to 80 per cent of the movie-going experience. And the centre speaker is the most crucial part of that. Say ‘hej’ to Emit 25C…

It could be argued that the centre channel is the most important part of any surround-sound system. It’s where the lion’s share of dialogue comes from in a movie, and it’s where the focal point of the music often comes from in a multi-channel mix. It’s crucial to get it right.

Emit 25C gets it right.

It’s essentially an Emit 30, turned on its side, with the mid/bass drivers placed either other side of the tweeter. The drivers are the same; the crossover is the same, with a different box and port-tuning. But that’s not doing it a disservice; quite the opposite. It means you get total consistency between the centre speaker and the two flanking it (whether those are Emit 10s, 20s, 30s or even 50s), along with any others you place around your listening position.

High-quality mid/bass drivers

Emit 25C uses the same 14cm MSP woofers as Emit 10 and Emit 30. MSP stands for Magnesium Silicate Polymer. It’s a material we developed decades ago, and have been refining ever since for use in all our most legendary speakers (including Confidence, Contour, Heritage Special and many more). MSP provides exactly the right combination of lightness, stiffness and damping to reproduce your material with all the detail the artist wants you to hear. Each cone is made in one piece, with an integrated dust-cap. The ‘balance ribs’ you’ll see in the centre are bonded directly to the voice-coil, so the whole mechanism moves as one piece – bringing with it immense control and detail over its sound.

The voice-coils themselves are made from lightweight aluminium wire, clad in a thin layer of copper. We’ve use aluminium here on the two-layer glass-fibre former because its weight doesn’t impede the driver’s movement. The copper layer means it can take more advantage of the magnetic energy generated by the dual-stacked ferrite magnet system. It magnifies that flux energy for more power – without sacrificing fleet-footed dynamics.

Top-end performance

Emit 25C has a high-performance Cerotar tweeter, along with all other Emit speakers – and the award-winning Evoke family. It’s based on the renowned Esotar Forty tweeter found in our Special Forty anniversary speaker, and features innovative technology that reduces unwanted resonance and optimises airflow. As with Evoke, Confidence and Contour i (among others), it also has a secret innovation: the Hexis. This is a small dimpled inner dome that reduces reflections to the back of the playing surface. You’ll hear its effect in the form of incredible detail resolution: sweet, smooth treble that doesn’t fatigue your ears – even during a long listening session.

Danish cabinet design

Emit 25C is available in three custom laminate finishes: Black, White and Walnut. They’re designed to complement each other, and blend seamlessly into your living room. That’s especially important for a centre channel, where (as much as we hate to say it), you should be spending more time looking at the picture above it than the speaker itself.

Emit 25C is the lynchpin of your home cinema speaker system. Power, control and finesse, rolled into one compact unit.

Features

Hi-fi starts with Emit - Designed and engineered in Denmark


The entire Emit family has been put through its paces in our world-class Jupiter measuring facility at Dynaudio Labs. We treat it exactly the same as we do every other speaker in our range: no stone left unturned.

Cerotar tweeter

Emit uses the highly regarded Cerotar tweeter from our Evoke series. It's a high-quality high-frequency driver inspired by our top-end Confidence and Heritage Special speakers, and includes the innovative resonance-defeating Hexis inner dome.

Clean and simple

Each speaker in the Emit range is designed to fit with modern lifestyles and interiors. Clean lines, simple finishes and minimalist Scandinavian looks – whether you're listening in stereo or have a full multi-channel system.

Specifications
  • Sensitivity: 87dB (2.83V/1m)
  • IEC power handling: 180 watt
  • Impedance: 4 Ω
  • Frequency response (± 3 dB): 53Hz - 25kHz (-6 dB 46 Hz - 35 Khz)
  • Box principle: Bass reflex rear double flared port
  • Crossover: 2.5-way
  • Crossover frequency: 1000/3500Hz
  • Crossover topology: 1ST order tweeter / 2nd order woofer
  • Midrange / Woofer: 14 cm MSP
  • Woofer: 14 cm MSP
  • Tweeter: Cerotar soft dome with Hexis
  • Weight: 10.98 Kg / 24.2 lb
  • Dimensions (W x H x D): 550 X 170,1 X 271,5 mm /  21.7 X 6.7 X 10.7 in
  • Dimensions with feet/grille (W x H x D): 550 X 170,1 X 284,5 mm /  21.7 X 6.7 X 11.2 in
You receive a 2 year warranty from the date of purchase for all of our high quality hifi-products.

If you observe any problem while using the product, you have the possibility to contact our friendly service team.

You can also easily manage your guarantee concern – without being obliged to – under the section My Account.

Warranty extension for Dynaudio products

To extend the warranty on your Dynaudio loudspeakers to a maximum of eight years, please register your speakers
online at http://www.register.dynaudio.com or contact your dealer for assistance. Registration has to take place within the first 3 months after the purchase of the speakers.

* Please note, that the extended warranty period is limited on active speakers and subwoofers.